How to make an angled cut on the table saw?

If you are confused about how to make an angle cut on the table saw, this post is a stop-shop for you. Here we will discuss the table saw settings and the placement of wood to make angle cuts with a table saw. 

Table saws not only offer decent cutting capacity, but they also allow fine cuts in confined spaces. They are stationary and allow precise angled cuts. In addition to ripping, a table saw can also be used to make a variety of angle cuts.

The table saw can perform cuts at different angles, i.e., 45 degrees, 60 degrees, 90 degrees, and more complex cuts. Despite the fact that table saws are not designed to make angle cuts, you can make angle cuts with them with a few adjustments.

Adjustments to make angle cuts

Here are some adjustments to make angle cuts with the digital gauge. With a digital gauge, you can precisely adjust your table saw blade angle to make angle cuts. The adjustments that a table saw requires to make angle cuts are given below. 

Set your table saw blade angle with the help of a digital angle gauge.

  • Remove the throat plate 
  • Use a bevel to adjust the angle of the blade.
  • Place the digital gauge on the table. 
  •  Turn on the gauge 
  • Let it be set at zero. 
  • Place it on the blade.
  • Check the angle of the blade 
  • Adjust it to your desired degree. 
  • Once it is set. 
  • Lock the bevel angle in position by tightening the adjustment screws. 
  • Place the throat blade back and make the angle cut precisely. 

A miter gauge can also be used to make angled cuts on the table saw. Normally, a miter gauge comes with the accessories of a new table saw, but you can also buy a more precise miter gauge. It can adjust the blade to any angle to make complex cuts. 

How to use a miter gauge to make angle cuts on the table saw?

There is a miter gauge attached to the table of your powered table saw. This device consists of a thin metal guide and a half-moon-shaped head pivoting at its connection point. It has a lock that locks the pivot to the desired angle you want to cut with a table saw (i.e., 45 degrees, 60 degrees, 90 degrees, etc).

After you place your wood on the table saw and tighten the gauge fence, you will get the angle you desire when feeding the work into the blades. 

How to make angle cuts with a taper jig?

Making angle cuts with the help of a taper jig is worth mastering to be a ninja in your field. Although it can be a little bit risky for beginners, once you learn the correct method to use it, it will become your everyday need. The taper jig method is the most widely used way to make angle cuts with the table saw. 

Here is a step-by-step guide to making angle cuts with a taper jig.

  • A taper guide has two adjustable legs that can be opened and closed according to the angle you want to make with your saw. 
  • It has a degree mark that helps in achieving the desired angle. 
  • First, make a layout line with a pencil on the board for the required angle. 
  • Put the taper jig with the blade. 
  • Bring the edge of your board against the taper jig. 
  • And measure both ends of the board until you get the same number on the measuring tape on both sides of the board. 
  • Open or close the legs of the taper jig to match the number. 
  • Once you have set the right angle, adjust the fence 
  • And raise the blade height 
  • Feed the workpiece into the blade with a sled. 
  • You can then get the wood cut to the angle you prefer.

Angled cuts require a sharp blade to process. A dull blade can destroy your workpiece if you try to make angle cuts with it. Learn how to sharpen table saw blade and check out Best portable table saw for fine woodworking.

Conclusion:

We have mentioned the most common methods of making angle cuts with a table saw. We hope you find this post informative and that all your confusion is resolved. Share your method of making angle cuts in the comment box. We will feature a few of them in our next article. 

Also, share your feedback and subscribe to our website to know all the tips and tricks of using the table saw.


Share post on

Allabouttool is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

Latest Posts

How to Adjust the Fence on a Rigid Table Saw Blog

How to Adjust the Fence on a Rigid Table Saw

At some point, you may need to adjust the fence on your Rigid table...

By brandonsmithaffiliate
How to Install Featherboard on Table Saw Blog

How to Install Featherboard on Table Saw

A featherboard is a great tool for ensuring accuracy and safety when working with...

By brandonsmithaffiliate
What to Consider When Purchasing a Portable Table Saw Blog

What to Consider When Purchasing a Portable Table Saw

A portable table saw is a versatile and powerful tool that can be used...

By brandonsmithaffiliate
Projects a Portable Table Saw is Best Suited For Blog

Projects a Portable Table Saw is Best Suited For

A portable table saw is a handy tool to have in any workshop. It's...

By brandonsmithaffiliate
Are portable table saws worth it? Blog

Are portable table saws worth it?

Are portable table saws worth it? These questions probably in your mind when you...

By brandonsmithaffiliate
Top 6 Best Drill Press Tables Table Saw

Top 6 Best Drill Press Tables

If you want to become a professional and get more accurate and precise results...

By brandonsmithaffiliate
Best Table Saw Push Blocks Table Saw

Best Table Saw Push Blocks

Investing in the best table saw push blocks is a wise decision if you...

By brandonsmithaffiliate
Top 10 Best Table Saw Miter Gauge Table Saw

Top 10 Best Table Saw Miter Gauge

A Table saw miter gauge makes your table saw more precise and accurate for...

By brandonsmithaffiliate