Steps to clean table saw blades

5 easy steps to clean table saw blade at home

Table saw blades, like everything else, grow dirty over time. A dirty blade produces a poor quality cut, burns wood, and becomes slow and difficult to operate. And a dirty blade can be harmful to both the instrument and the operator. It needs a simple steps to clean table saw blade to restore it to its original condition. Naturally, you should use a sharp blade to avoid damaging your tool or yourself. In this article, I will tell you the reasons behind the dullness of your table saw blade and how you can clean your table saw blades easily at home.

Steps to clean table saw blade

  • Unplug the table saw and release the blade. 
  • Wipe away the dust with a piece of cloth. 
  • Soak it in a mixture of water and detergent for a few minutes.
  • Use the brush to clean it and wash it with clear water. 
  • Dry it. 
  • Fix it back.

Why do table saw blades become dull and dirty?

The pitch and glue from the wood you’re cutting will jam your blade’s carbide tips, making them less sharp and inefficient, resulting in poor cuts and making it difficult to operate.

Cleaning a saw blade is as simple as rinsing a razor blade. After completing every two to three projects, just give 20 minutes to clean it and make it shine as new.

What do you need to clean a table saw blade at home?

You don’t need much to clean your table saw blades at home. Gather the items listed below from your garage and start cleaning your saw blade.

  • A bucket
  • Detergent 
  • Rinse and pitch remover (optional).
  • Soft bristle brass brush
  • Steel wool
  • Paper towel
  • Silicon spray (optional).
  • Dry tool lubricant.

Detail guidelines how to clean table saw blade

These methods show how to clean table saw and circular saw blades in a quick and simple manner.

Unplug your table saw

The idea of cleaning the table saw blade while it is fit in the saw unit is dangerous; for safety, unplug the table saw first.

Release the blade

Switch off the blade’s button, take a wrench to untighten the arbor nut, and release the blade carefully. 

Prepare a bath for the blade

Take one portion of liquid soap (or rinse and pitch remover available on the market) and three portions of lukewarm water and mix them in a bucket. 

Soak the blade

Place the blade flat in the container and fully soak it in the cleaning solution. Allow the blade to soften the resin residue by leaving it in the resin remover. Let it remain socked for 20 minutes. 

If your blade is dusty, it’s a good idea to use a stiff wire brush to remove the majority of the dirt before putting it in the water.

Note: Refer to your product’s description for specifics on how long you should leave it. Soaking it too long can degrade the metal in your blade. This could diminish the blade’s integrity, making them susceptible to breaking. 

Clean it with a brush

Using a toothbrush or a small brass brush, scrub the blade’s teeth and any gunky spots until clean.

Remember that the blade can cause you to cut your finger, so keep your fingers away from it and wear protective gloves.

Rinse with clear water

After cleaning all the dirt and grease from the blade, please take off the blade from the tub and wash it with clear water. Detergents or any cleaner left on the blade might cause corrosion.

Dry the blade using a paper towel

It’s important to make sure the blade is completely dry after washing. Otherwise, it’ll rust soon. Dry it using paper towels first, but if you want to ensure the job is done properly, you can use a hairdryer to remove any remaining moisture.

Use dry lubricant

To make it shine and work efficiently, use a dry lubricant. This is an optional step.

We hope this post was informative and you found answers to your questions. Share your thoughts on this article in the comments box below, and feel free to bring up any issues you may have with any woodworking tool; our team will respond as soon as possible.


Posted

in

by

Tags:

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *